Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
The content listed below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is without a doubt engaging. Give it a try and draw your own conclusions.
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is easily available, the project can move easily; if you have to open a wall to eliminate the old bathtub as well as place the brand-new tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the brand-new one. Make sure you have qualified yourself for the work and also fit trying it. As opposed to employing a specialist to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your washroom if you have actually already bought a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as product checklist should consist of the following:
Getting ready for the Installment
First of all, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather bothersome as a result of the restricted gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. Once the supply pipes have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Using the two wooden boards under its feet, put the tub in the needed setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level checks out level.
To set up taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the various other tap.
Turn on the supply of water and examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow outlet as well as the normal outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has been utilized at least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers are in area between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind should be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Give a comment down below. We will be interested to find out your thoughts about this blog posting. We are looking forward to see you back again in the near future. If you please take a moment to share this blog if you enjoyed reading it. Thanks for your time. Please come visit our site back soon.
Need Help? Hire Us Now! Report this page